Installing a new piece of drywall or repairing a hole in existing drywall can be a rewarding process, but the job isn’t done once the drywall is screwed in place. The drywall piece still has to be finished to make it blend in seamlessly with the rest of the wall. A proper finishing technique will make it impossible for anyone to tell where the new piece of drywall begins or ends. Here are some tools that can be used to get the finishing process done.
A mandatory tool for finishing drywall is a drywall knife. The knife is used to mix the compound and spread it onto the wall to fill in seams and dents. Multiple coats of drywall compound will be used to make the seamless finish so that you will need knives of different sizes, generally one at five inches, one at six inches, and one at ten inches. Disposable knives can be used, and are usually preferred because of how inexpensive they are, but if you spend a little more, you can have a metal tool will last quite a while, as long as you clean it after use.
Once the drywall compound has dried, it will need to be sanded to remove any imperfections and make the wall completely flush. Small sanding jobs can be done with a small section of the sand paper. For a larger job, or work that must be done on the ceiling, a sanding pole with changeable sheets can be used. The pole can use a mesh sheet that will let dust from the drywall pass through it. A sanding sponge with a smooth side and an abrasive side can be used to touch up spots on the wall.
If you’re faced with the task of mixing a container of the compound to use on the wall and want to do it with a little speed, you can use a drill with a mixing paddle. The paddle attachment will push down any water that has collected on the surface of the compound and mix it thoroughly. It only takes a few moments to mix with the drill and paddle, and you save more time and energy than if you mixed the compound by hand.
Although a utility knife is small, it can be quite handy when doing a finishing job. The knife can be used to cut the compound container open before you start the job. It can also be used to cut the wall tape that will be placed over the seams of the drywall before the compound is applied. Be sure to use a knife with locked in interchangeable blades, rather than ones that snap off.
All you need is the right tools to finish a wall. Before finishing your drywall, make sure you have everything that you need, and the job will be over before you know it.
It does not matter how big or small the damage is; the damage will never go away not unless you do something about it. There are many factors that can cause damages to a Drywall. This makes some drywall repairs easy to repair, while others are not. However, with the right tools and materials, a person can perform few maintenance as well as improve their home. In cases where the problem is severe, it is wise to call an expert. For example, if the problem can affect structure integrity, it is wise to call a professional.
Well, if you are looking to improve your property and you are looking to start with drywall repairs, then you are in the right place. Below are steps to make such improvement:
The Steps For Small Holes
If the hole on the wall is small, then be glad because it will not take you more than 10 minutes to repair it. The first thing to do is clean the hole with a blade knife or something sharp. Cut the hole at an angle so that the outer part of the hole is bigger than the inner part. Fill the hole with painter’s putty. While at it, make sure it levels with the wall surface. First, let it dry before sanding the area lightly to make it smooth. Spackle more putty if there is a need to or repeating the step.
The Steps For Medium Holes
If the hole is medium, it is wise to use a drywall metal patch. How do you do this? Begin by sanding the surface around the hole to make it smooth. Wipe off the dust, then peel the paper patch of the metal drywall and firmly press it in place with the mesh facing outward. Using drywall compound and spread it over the patch to cover the edges. After smoothing it put, let it dry. Sand it gently until it is smooth. Do this until the patch cannot be detected.
The Steps For Large Holes
Larger holes require patches made of drywall. It is wise to ensure it has the patch is thick as the wall. Cut a squire of drywall slightly larger in comparison to the hole. Draw an outline of the patch around the hole using a pencil. It is paramount to check for electrical cords and plumbing lines where you plan to cut. Use a drywall saw to cut out the drawn area.
Screw two wooden boards (one of the top and the second at the bottom) behind the drywall to prevent it from falling through. Screw the drywall patch to the wooden boards and using compound drywall spread it onto the area and then add mesh. Sand the area until it is undetectable.
Drywall has been around since the 1940′s and has grown into the main building source for walls and ceilings. There are two main reasons why drywall has become so popular. Drywall is dirt cheap, it cost about 8 dollars for one sheet. Repairing drywall is very easy, all you need is some easy to use tools and you can start hanging drywall too. Just follow the guidelines!
Check Drywall Tips before repairing!
1. The first thing that you need before you learn to hang drywall is to check your local building codes.
Also, before you begin repairing drywall, you need to gather the tools needed. You need a thin lightweight trowel because a light touch is key when making seams on your drywall. You will also need paper tape. This will produce a joint that is strong when you also use a compound with it.
2. The next step before you begin to repair drywall is to remove all of the old drywall that is there.
You will need to rip the old drywall from the studs and the ceiling. You want to make sure that you do a good job when removing the old drywall, this will make your new installation of drywall much easier. You may also want to get out a broom to sweep up all the little debris. You will also want to remove all the nails from the studs, you want to make sure that you have a flat surface to hang your drywall.
3. The next thing that you will need to do is measure the square footage of your walls and ceilings.
You want to end up with as few seams as possible because taping seams are the hardest thing to master when you are learning how to repair drywall. A typical drywall sheet for walls is 4 by 8 feet and they are typically installed so that the long side is from the floor to the ceiling. Other places will offer drywall sheets that are longer but every sheet will be 4 feet wide.
4. When you go to purchase your drywall make sure to get larger drywall pieces.
Taping is an area where most amateurs have trouble. If you have a second person helping you handle the larger pieces then this should not be an issue. If you need to store the drywall make sure that you store the drywall flat so that it won’t bend or break. When you go to purchase your drywall at your local store you can ask some question to the workers. They should be able to help you out a lot.
5. When you start to repair drywall, you need to hang them from the top down, this means that you need to start with the ceiling first.
Before you begin to hang drywall you need to check the joist of your ceiling for any bowed joists. If your joists are bowed then you will have to use drywall shims. If your ceiling is 15 feet long then you should use the longest drywall sheet available because you will have fewer seams this way to tape. Use a helper to hold the drywall sheet up and hammer in some drywall nails about a foot and a half apart from each other. Then just cut the excess drywall using a drywall knife. After you finish the ceilings, you should move onto the walls in the same fashion.
6. When hanging drywall you want to make sure that you protect your wiring.
You can easily pierce some wires from the drywall nails and this will create a fire hazard. To solve this problem you need to install steel plates over the wires and nail them to the studs. Another problem when installing drywall on the walls is electrical outlets. Just measure the box and transfer it onto the drywall and if the measurements are not perfectly lined up then just use a drywall rasp.
7. Next, you need to start on the outside corners and to do this you need to cut metal corner beads.
Then you need to make sure that it is properly aligned and then nail one side into the wall and then the second side. You need to make sure that the nails are a foot and half apart and for the inside, corners spread compound on each side.
8. The final step is to start taping the seams.
You need to tape the outside seams first. You do this by using at least a 4-inch wide knife to spread the compound around the seams. Then press paper tape into the joints and wipe away any excess. When this drys, you need to apply a second coat of the compound and when this drys, you will need to sand it down and apply another 2 more coats. When you begin taping the seams you may notice that the drywall may have some really huge gaps but you should not worry because the compound along with the tape will help smooth over everything.
These are all the basic tips for you to learn how to repair drywall. Any two person team that knows some very basic carpentry skills will be able to complete a small room in a weekend. The hardest part to get the hang of is the taping. If you are still not sure that you can do this, then you can go to your local store to ask some questions, you can also contact a drywall professional and ask to spend the day with them to see how they do it and there are a bunch of videos and books online on the subject as well. With the wealth of information online you should not have any problems with your first drywall repairing job.